Image similar
Phoenix Contact 1158272 CHARX PS/3AC/500DC/20KW DC power unit
EAN:
Part number:
Item no:
Datasheet (PDF)
Technical specifications
- Product family: Charx Power advanced
- Connection type 2x RJ45
- Width 483 mm
- Height: 89 mm
- Depth: 540 mm
- Ambient conditions: Environmental conditions
- Protection class: IP20
- Ambient temperature (operation): -25 °C ... 60 °C
- Ambient temperature (storage/transport): -40 °C ... 60 °C
- Standards/regulations: CSA C22.2 No. 107.1-16
- 19" rack mounting
- Insulation properties: Insulation properties
- Overvoltage category: Overvoltage category
- Pollution level: 2
- Permissible air humidity (operating): ≤ 95% (non-condensing)
- Stripped insulation length 10 mm (rigid / flexible);10 mm (wire end sleeve)
- Height unit 2 HE
- Short circuit resistance (SCCR) 10 kA
- Transmission speed: 125 kBit/s (GCP protocol);500 kBit/s (BCT protocol);1
- Protection class: I
- Rated output: 20 kW
- Number of interfaces: 1
- Transfer length: Max. 20 m.
- Connection technology: Connection technology
- Rated input voltage range: 350 V DC ... 500 V DC
- Input voltage range: 300 V DC ... 600 V DC
- Nominal power intake 22170 VA
- Efficiency: > 96.5% (400 V AC, 50 % < out < 100 %);> 97% (600 V DC, out > 50 %)
- Protection against overvoltage at output (OVP): > 550 V DC
- Input: Input
- Wire connection: Conductor connection
- rigid: 6 mm² ... 10 mm²
- flexible: 6 mm²
- Flexible with wire-end sleeve without plastic sleeve: 6 mm²
- Flexible with wire-end sleeve with plastic sleeve: 6 mm²
- Rigid (AWG): 10 ... 8 (Cu)
- Output: Output
- Digital: Digital
- Number of phases: 3
- Insulation voltage input/output: 4240 V DC (reinforced insulation)
- Article dimensions: Article dimensions
- Operating height: ≤ 2000 m
- Power conversion equipment standard
- EMC requirements Emission of interference: EN 61000-6-3
- EMC requirements Immunity: EN 61000-6-2
- AWG 10
- Mains type DC network
- Power factor (cos phi) 0.99
- Derating- > 45°C (2.5 %/K)
- Control deviation: < 1 % (current deviation load variation static 20 % ... 100 %);± 0.2 % (input voltage change ±20 %)
- Polarity marking: 1x +/-, 1x +/-, 1x +/-
- CAN bus: CAN bus
- CAN bus interface
- Supported protocols: CAN 2.0B
- Lock: Snap hook
- Transmission physics: Cable-bound
- Topology: Daisy chain
- Terminating resistance: 120 Ω (terminate end user)
- Total distortion (THDi): 0.02%
- Output voltage range: 150 V DC ... 500 V DC
- Output current range: 0 A ... 66 A
- Power loss Stand-by < 5 W
- Designation: Output
- Insulation voltage input, output/housing 2614 V DC (base insulation)
- Volume flow 160 m³/h (45 °C)
- Air flow direction: From front to back
- Noise level < 65 dB (1 m)
- IEC 60664-1: III (AC/DC RECERTIFIED FROM < 300 V AC);II (DC)
- Safety requirements for power semiconductor converter systems and equipment - Part 1: General information: Safety requirements for power semiconductor converter systems and equipment - Part 1: General information
- Conductive charging systems for electric vehicles - Part 21-2: EMC requirements for external charging systems for electric vehicles: Conductive charging systems for electric vehicles - Part 21-2: EMC requirements for external charging systems for electric vehicles
- Input current 3x 20 A (DC)
- Switch-on delay < 2 s.
- Overshooting behavior: < 1% (switch-on)
- Number of power modules as CAN BUS nodes: Max. 48 (GCP Protocol);max. 32 (BCT Protocol)
- Insulation voltage input, output/signal, communication: 4242 V DC (reinforced insulation)
- Isolation voltage signal, communication/housing: 707 V DC (base insulation)
- Over temperature protection (OTP): > 65 °C (hysteresis 5 K)
- Conductive charging systems for electric vehicles - Part 1: General requirements: Conductive charging systems for electric vehicles - Part 1: General requirements
- Conductive charging systems for electric vehicles – Part 23: DC power supply systems for electric vehicles: Conductive charging systems for electric vehicles – Part 23: DC power supply equipment for electric vehicles
- Standard for Safety for Electric Vehicle (EV) Charging System Equipment: Standard for Safety for Electric Vehicle (EV) Charging System Equipment
- Input frequency: 3x 50 Hz 60 Hz ±10 %
- Rated short-term current strength (ICW) 10 kA
- Rated surge current strength (IPK) 17 A.
- Duration (ICW): 60 ms
- Specification: CANopen standard
- Power conversion equipment: Power conversion equipment
- Product type
DC power unit
- Protection class
I
- Depth
540 mm
- Height
89 mm
- Width
483 mm
IP20
- Recess height
89 mm
- UKCA
yes
Documents & Downloads
Datasheet
Datasheet 3565383 Phoenix Contact 1158272 CHARX PS/3AC/500DC/20KW DC power unit
User & Safety Instructions
User & Safety Instructions 3565383 Phoenix Contact 1158272 CHARX PS/3AC/500DC/20KW DC power unit
Description
Charx Power advanced, quick-charge module for DC charging stations, 19" rack mounting, input: 3-phase, output: 150 V DC...500 V DC / 0 A...66 A.
This text is machine translated.
This text is machine translated.