Image similar
Safety relay PSR-ME20-3NO-1NC-24DC-SC-SET35 Phoenix Contact Operating voltage: 24 V DC 2 breakers (W x H x D) 22.5 x 112
Packaging type
Package
Product type
Safety relay
Connector
Screw-fit
Operating voltage
24 V DC
Type
PSR-ME20-3NO-1NC-24DC-SC-SET35
Datasheet (PDF)
EAN:
Part number:
Item no:
Technical specifications
- Product family: PSRclassic
- Connection type: screw terminals.
- M3 screw thread
- Tightening torque: 0.5 Nm ... 0.6 Nm
- Conductor cross-section flexible: 0.2 mm² ... 2.5 mm².
- Conductor cross-section rigid: 0.2 mm² ... 2.5 mm².
- Wire cross-section AWG: 24 ... 12
- Width 22.5 mm
- Height: 112.2 mm
- Depth: 114.5 mm
- Material: housing: PA
- Ambient conditions: Environmental conditions
- Protection class: IP20
- Ambient temperature (operation): -20 °C ... 55 °C (observe De-rating)
- Ambient temperature (storage/transport): -40 °C ... 70 °C
- Mounting type: Rail mounting
- Insulation properties: Insulation properties
- Over voltage category III
- Pollution level: 2
- Vibration (operation): 10 Hz ... 150 Hz, 2g
- Stripped length: 7 mm
- General: General
- Mounting position: Vertical or horizontal
- Maximum power loss at rated conditions: 16.6 W (US = 26.4 V, Il² = 72 A², Ptotal max = 2.2 W + 14.4 W )
- CE CE
- Connection technology: Connection technology
- Note for application: Only for industrial use
- Power consumption 2 mA (type At US at S34);3 mA (typ. For us at S35)
- Wire connection: Conductor connection
- Switching frequency: Max. 0.5 Hz
- Mounting instructions: See derating curve
- Operating height: ≤ 2000 m (over NN)
- Max. ass. Humidity (operating): 75% (average, 85% occasional, no condensation)
- Shock 15g
- Protection circuit: Suppressor diode
- Status display 2 x LED (green)
- Switching voltage: Min. 10 V AC/DC; MAX. 250 V (AC/DC)
- Designation A1/A2
- Application: Emergency stop;protective door;light lattices
- Supply: Supply
- Colour (housing): Traffic gray B (RAL 7043)
- Min. Switch-on current 10 mA; max. 6 A
- Description of the output: 2 NC parallel, not safety-related, potential-free
- Power supply 1 x LED (green)
- Contact version 2 NC parallel
- Continuous current 6 A
- Rated insulation voltage 250 V
- RATED CONTROL CIRCUIT SUPPLY VOLTAGE US: 24 V DC -15 % / +10 %
- Rated control feed current IS: Typ. 70 mA (with US)
- Safety specifications: Safety specifications
- Mechanical life: 10x 106 switching cycles
- Response time typical: 200 ms (automatic start);200 ms (manual, monitored start)
- Drop-off time typical: 25 ms (when requested via the sensor circuits);60 ms (when requested via A1)
- Contact material: AgSnO2
- SWITCHING RATING 3 A (AC15);2 A (DC13)
- Output 6 A gL/gG
- Relay type: Electromechanical relay with forced contacts according to IEC/EN 61810-3
- Times: Times
- Type. US response time: 200 ms (when controlled via A1)
- Readiness time: < 500 ms (according to requirement of safety function)
- Rating type 100 % ED
- Rated surge voltage / insulation: Basic insulation 4 kV between all output current paths;basic isolation 4 kV between all output current paths/logic paths and housing;secure separation, reinforced insulation 6 kV between 250 V load current paths and 24 V logic paths
- Filter time: No test pulses allowed
- Number of outputs: 1
- Switching capacity: Min. 100 mW
- Quadr. Total current 36 A2
- Safety specifications: EN ISO 13849: Safety specifications: EN ISO 13849
- Performance level (PL): D.
- Safety Integrity Level (SIL) 2
- Safety specifications : EN IEC 62061: Safety specifications: EN IEC 62061
- Protection class Installation location minimum: IP54
- Max. ass. Humidity (storage/transport): 75% (average, 85% occasional, no condensation)
- Description of the input: Not safety-related
- Number of inputs: 2
- Input voltage range "0" signal: 0 V DC ... 5 V DC (S10, S12)
- Input voltage range "1" signal: 20.4 V ... 26.4 V
- plug connection: yes
- 1 and 2 channel control
- Power consumption in US: Typical 1.68 W
- Stop category: 0
- Security specifications : IEC 61508 - High-Demand: Security specifications: IEC 61508 - High-Demand
- Technical data: IEC 61508 - Low-Demand: Security specifications: IEC 61508 - Low-Demand
- Restart time: < 1 s (boot time)
- Input current range "0" signal: 0 mA ... 2 mA
- Concurrency: ∞
- Max. Permissible total line resistance: 50 Ω
- Digital: Start circuit (S34, S35): Digital: Start circuit (S34, S35)
- Relay: Enable current paths (13/14, 23/24, 33/34): Relay: Enable current paths (13/14, 23/24, 33/34)
- Relay: Signalling current path (41/42): Relay: Signalling current path (41/42)
- Digital: Sensor circuit (S10, S12, S22): Digital: Sensor circuit (S10, S12, S22)
- Packaging type
Package
- Product type
Safety relay
- Type
PSR-ME20-3NO-1NC-24DC-SC-SET35
- Connector
Screw-fit
- Operating voltage
24 V DC
- Response time
200 ms
- Contact type
2 breakers
- Switching voltage (max.)
250 V DC/AC
- Performance level
PL d
- Safety integrity level
SIL 2
- Safety rating
3
- Certification (sensors)
CE
- Features
Incl. signalling current path
IP20
- Operating temperature (min.)
-20 °C
- Operating temperature (max.)
55 °C
- Depth
114.5 mm
- Width
22.5 mm
- Height
112.2 mm
- Dim
(W x H x D) 22.5 x 112.2 x 114.5 mm
- Content
1 pc(s)
- UKCA
yes
Documents & Downloads
Datasheet
Datasheet 3582801 Safety relay PSR-ME20-3NO-1NC-24DC-SC-SET35 Phoenix Contact Operating voltage: 24 V DC 2 breakers (W x H x D) 22.5 x 112
User & Safety Instructions
User & Safety Instructions 3582801 Safety relay PSR-ME20-3NO-1NC-24DC-SC-SET35 Phoenix Contact Operating voltage: 24 V DC 2 breakers (W x H x D) 22.5 x 112
Description
Set of 35 safety relays for emergency stop, protective doors and light grids up to SIL 2, CAT. 3, PL d, 1- or 2-channel operation, automatic or manual, monitored start, 3 release current paths, 1 detection current path, US = 24 V DC, pluggable screw terminals
This text is machine translated.
This text is machine translated.